Product Code: LXA-102-16A
2-Relays Outputs with / 2 Digital Inputs and / 1 Analog Input
The device is a modular installation device (MDRC) which is used home and building automation systems. It is intended for installation in flush mounted box. Physical address assignment and parametrization are carried out with ETS. The device is supplied with KNX bus energy, does not need any additional power supply. The device is ready for operation after connecting the bus voltage.
Product Characteristics
- 2 Relay Outputs (16A, 230VAC @50-60 Hz)
- Lighting Function
- Shutter & Blind Function
- Heating Function
- Operation as NO or NC Contacts
- Timing Function: Switch On/Off Delay, Staircase and Flushing Functions
- Working Hours Counter Function
- Shutter Alarm Function
- Shutter Automatic Sun Alarm Function
- 2 Digital (Dry Contact) Inputs
- 1 Analog Input
- Sensor Connection: PT1000 or 0-10V Sensor
- Logic Function
- Scene Function
- Data Type Converter Function
- Configurable with ETS5
- Programming LED and Button
- Easy Installation to Flush Mounted Box
- Production in Germany, certified according to ISO 9001 and KNX
- 2 Years warranty
Please Read Carefully Before First Use
- Electrical equipment must be installed and suited only by qualified electricians
- Failure to observe any of the installation instructions may cause damage to the device and result in fire and other hazards
- Observe the current accident prevention regulations
- Before working on the device or before replacing any connected loads, disconnect the supply voltage (by cutting out the circuit breaker) to avoid the risk of an electric shock
- Make sure during the installation that there is always sufficient insulation between the mains voltage and the bus
- Do not open the device and do not use it outside the scope of the technical specifications
Connection Diagram
Scale Drawing
Technical Data
| Type of protection | IP 20 | EN 60529 |
| Safety class | ıı | EN 60664 |
| Power Supply | Voltage | 21V... 30V DC, SELV |
| Current Consumption | <10mA | |
| Mounting | Flush Mounted Box | |
| Output | Number | 2 |
| Switching Voltage | 230 VAC; @50/60 Hz | |
| Switching capacity 250 VAC | 16A, 100A Inrush | |
| Maximum switching power | 4000 VA | |
| Output Connection | Pluggable Connector | 4 Position Wire to Board Terminal Block 45° |
| Conductor Cross Section | Solid Wire: 20-14 AWG / 0.518-2.08 mm² | |
| Stranded Wire : 20-14 AWG / 0.518-2.08mm² | ||
| Wire Stripe Lenght | 7.5-8.5 mm | |
| Pitch | 3.5 mm | |
| Rated Values | Lamps Incandescent lamp load | 3680W |
| Fluorescent lamp load | 250VAC 16A, 102A inrush current | |
| Tungsten lamp load | 120VAC, 600W | |
| Capacitive Load | 70uF 10A cosQ=0.9 | |
| Electronic Ballast | 277VAC 2A | |
| Digital Input | Number | 2 binary inputs |
| State | Dry contact | |
| Scanning Voltage | 3V3 pulsed | |
| Current | 1mA | |
| Analog Input | Number | 1 |
| Voltage | Pt1000, DC 0-10V | |
| Operating Elements | Programming Button | |
| Programming LED | ||
| Temperature Range | Operation | -5°C / +45°C |
| Storage | -20°C / +70°C | |
| Humidity | Maximum air humidity | 85% no moisture consendation |
| Flammability | Non-flammable product | |
| Dimensions | L:22mm W:42mm H:42mm | |
| Weight | 40 gr with cables | |
| Certification | KNX Certified |
ETS Database
 KNX Flush Mounted Actuator ETS Database |  Download ! |