Product Code: LXA-148-010
The iluxusdesign 0…10V Module with 8 analog outputs can be used for 0-10V LED drivers for dimming operations or 0…10V operational valves for HVAC operations. It has 4 analog inputs, PT1000, NI1000 sensors and 0…10V voltage, 0…20 mA current via 500 Ohm shunt connections are supported. Included 4 digital inputs, can be connected as dry contact.
KNX Analog IO (0/10V)Product Characteristics
- 8 Analog output channels DC 0…10V
- 4 Analog input channels
- 4 Digital input channels
- Dimming operations
- HVAC operations
- Configurable with ETS
- Programming LED and buttons
- KNX Bus LED
- Sensor connections: PT1000 (Brightness, Temperature, Rain, Humidity,Wind, etc.)
- Feedback operations (only in bus operation)
- Easy installation to 35mm DIN Rail
- Production in Germany, certified according to ISO 9001 and KNX
- 2 years warranty
Please Read Carefully Before First Use
- Electrical equipment must be installed and suited only by qualified electricians
- Failure to observe any of the installation instructions may cause damage to the device and result in fire and other hazards
- Observe the current accident prevention regulations
- Before working on the device or before replacing any connected loads, disconnect the supply voltage (by cutting out the circuit breaker) to avoid the risk of an electric shock
- Make sure during the installation that there is always sufficient insulation between the mains voltage and the bus
- Do not open the device and do not use it outside the scope of the technical specifications
Connection Diagram
Scale Drawing
Technical Data
| Type of protection | IP 20 | EN 60529 |
| Safety class | ıı | EN 60664 |
| Power Supply | Voltage | 21V... 30V DC, SELV |
| Current Consumption | <10mA | |
| Mounting | Flush Mounted Box | |
| Output | Number | 2 |
| Switching Voltage | 230 VAC; @50/60 Hz | |
| Switching capacity 250 VAC | 16A, 100A Inrush | |
| Maximum switching power | 4000 VA | |
| Output Connection | Pluggable Connector | 4 Position Wire to Board Terminal Block 45° |
| Conductor Cross Section | Solid Wire: 20-14 AWG / 0.518-2.08 mm² | |
| Stranded Wire : 20-14 AWG / 0.518-2.08mm² | ||
| Wire Stripe Lenght | 7.5-8.5 mm | |
| Pitch | 3.5 mm | |
| Rated Values | Lamps Incandescent lamp load | 3680W |
| Fluorescent lamp load | 250VAC 16A, 102A inrush current | |
| Tungsten lamp load | 120VAC, 600W | |
| Capacitive Load | 70uF 10A cosQ=0.9 | |
| Electronic Ballast | 277VAC 2A | |
| Digital Input | Number | 2 binary inputs |
| State | Dry contact | |
| Scanning Voltage | 3V3 pulsed | |
| Current | 1mA | |
| Analog Input | Number | 1 |
| Voltage | Pt1000, DC 0-10V | |
| Operating Elements | Programming Button | |
| Programming LED | ||
| Temperature Range | Operation | -5°C / +45°C |
| Storage | -20°C / +70°C | |
| Humidity | Maximum air humidity | 85% no moisture consendation |
| Flammability | Non-flammable product | |
| Dimensions | L:22mm W:42mm H:42mm | |
| Weight | 40 gr with cables | |
| Certification | KNX Certified |
KNX Database
 KNX Analog IO Technical Database |  Download ! |